Announcement

Collapse
No announcement yet.

weather radar in HSTouch

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #61
    Aha, sorry. No, no options documented for the meteogram.

    Comment


      #62
      Originally posted by U5tabil View Post
      I found the problem just before you posted now

      The reason was that i was using /html/images/YR..... but it should be /images/YR.... without the /html....
      I'm trying to use my ISP address now. but it only seem to work when I am on local network with local IP address. Is there something i need to do to get it working with a Dynamic DNS address?
      Certified installer for HomeSeer, Control4, KNX and Eaton/xComfort

      Comment


        #63
        I'm not too familiar with HomeSeers own remote services as I don't use them. I would recommend forwarding your question to HST or use post a question in the generic HS3 part of this forum.

        Traditional dynamic DNS requires port forwarding in the router to access the local machine and should be quite straight forward. Can you access other content remotely?

        (personally I use VPN to connect to my home network)

        Comment


          #64
          Originally posted by Toby View Post
          I'm not too familiar with HomeSeers own remote services as I don't use them. I would recommend forwarding your question to HST or use post a question in the generic HS3 part of this forum.

          Traditional dynamic DNS requires port forwarding in the router to access the local machine and should be quite straight forward. Can you access other content remotely?

          (personally I use VPN to connect to my home network)
          Yes i can connect and controll HS remotely, but its just this radar that shows blank when on remote. Its very strange...
          Certified installer for HomeSeer, Control4, KNX and Eaton/xComfort

          Comment


            #65
            You can control using the webpage or any of the other means?
            have you configured port forwarding for port 80 (or the used web port)?

            Do you see any error in the HS log when trying to view the image remotely?

            if it works locally then I can only think of a few possible errors:
            - port-forwarding not configured or working properly
            - HS3 webserver has some access restrictions for users when viewing remotely.

            if you can view other images in the image folder then one can rule out the first one. the last one I would expect would generate an error in the HS3 log

            Comment


              #66
              I i try access the page from browser even on phone on 4g I manage to get the radar showing after login. But in HSTouch the radar is white and blank.

              So it is not the port forwarding that is wrong. But something else that I don't understand.

              Maybe there is some password in here? Can I add password to the http link in text?

              Sent from my E6853 using Tapatalk
              Certified installer for HomeSeer, Control4, KNX and Eaton/xComfort

              Comment


                #67
                This sounds like a access problem, I'm guessing that since you have to login to view the image when using the web page, the local url configured in HS Touch will not work when remote - Assuming you have configured a remote URL in HS touch it will not work without username/ pw as HS touch and the webpage uses different port and services.

                In the old days one could use http://usernameassword@iport/image/Path/ in browsers, but i know this have been removed from at least some modern browsers. HSTouch might still support this.

                Comment


                  #68
                  Originally posted by Toby View Post
                  This sounds like a access problem, I'm guessing that since you have to login to view the image when using the web page, the local url configured in HS Touch will not work when remote - Assuming you have configured a remote URL in HS touch it will not work without username/ pw as HS touch and the webpage uses different port and services.

                  In the old days one could use http://usernameassword@iport/image/Path/ in browsers, but i know this have been removed from at least some modern browsers. HSTouch might still support this.
                  It was at least a try. But I am getting bad request with this
                  Certified installer for HomeSeer, Control4, KNX and Eaton/xComfort

                  Comment


                    #69
                    Originally posted by U5tabil View Post
                    It was at least a try. But I am getting bad request with this
                    Remind me again, the reason you couldn't use the image in the device was that it was?

                    Sent fra min E6653 via Tapatalk

                    Comment


                      #70
                      Originally posted by Toby View Post
                      Remind me again, the reason you couldn't use the image in the device was that it was?

                      Sent fra min E6653 via Tapatalk
                      Its not the portforwarding as I can access it from web outside. But trying to access the

                      http://ispaddressort/images/YR/radar.html i need to log in. So it has to do with credentials.
                      Certified installer for HomeSeer, Control4, KNX and Eaton/xComfort

                      Comment


                        #71
                        Originally posted by U5tabil View Post
                        Its not the portforwarding as I can access it from web outside. But trying to access the

                        http://ispaddressort/images/YR/radar.html i need to log in. So it has to do with credentials.
                        Yes, but why could you not use the normal image attached to the hs device rather than messing around with this html files?

                        Sent fra min E6653 via Tapatalk

                        Comment


                          #72
                          Originally posted by Toby View Post
                          Remind me again, the reason you couldn't use the image in the device was that it was?

                          Sent fra min E6653 via Tapatalk
                          Ah yeah well it was not working properly. And the image was to small, so i could not scale it properly in HSTouch.
                          Certified installer for HomeSeer, Control4, KNX and Eaton/xComfort

                          Comment


                            #73
                            I managed to get it working adding credentials like usernameassword@iport/location worked. The problem was the password. The password was containing %#"% in it as well as numbers etc. And HSTouch does not like this. Making a more simple password only with letters and numbers made the trick!
                            Certified installer for HomeSeer, Control4, KNX and Eaton/xComfort

                            Comment


                              #74
                              Originally posted by U5tabil View Post
                              I managed to get it working adding credentials like usernameassword@iport/location worked. The problem was the password. The password was containing %#"% in it as well as numbers etc. And HSTouch does not like this. Making a more simple password only with letters and numbers made the trick!
                              Fantastic glad to hear.
                              Yes, these special characters does not convert easily to a URL.

                              Comment


                                #75
                                Just wondering a bit. Is it possible to rotate the image 90 degrees?

                                Code:
                                <html lang="en"> 
                                <head>
                                <META HTTP-EQUIV=Refresh CONTENT=600>
                                </head> 
                                <body leftmargin="0" topmargin="0" marginwidth="0" marginheight="0">
                                <img src="http://api.met.no/weatherapi/radar/1.4/?radarsite=western_norway;type=reflectivity;content=animation;size=large" height="100%" width="100%"></img>
                                </body>
                                </html>
                                Certified installer for HomeSeer, Control4, KNX and Eaton/xComfort

                                Comment

                                Working...
                                X