With the rfxmngr program everything is OK
Initialisation OK
I can receive ch1 On, Ch1 Off, Ch2 On and Ch2 Off
And I can also send ch1 On, Ch1 Off, Ch2 On and Ch2 Off
With the plugin I can catch the remote signal
When I create the output device I set the address corresponding the ID of the AC module.
But I don't find how to set the Unit (1, 2 or 3)...
So when I try to change the state of the homeseer created device,it's not the correct command that is sent, so the module doesn't react...
May be I'm doing something wrong...
Thanks for your help
Initialisation OK
Code:
================================================ Reset receiver/transceiver:0D 00 00 0C 00 00 00 00 00 00 00 00 00 00 ================================================ Get Status:0D 00 00 0D 02 00 00 00 00 00 00 00 00 00 ------------------------------------------------ 0D01000D02534300000500000000 Packettype = Interface Message subtype = Interface Response Sequence nbr = 13 response on cmnd = Get Status Transceiver type = 433.92MHz Firmware version = 67 Hardware version = 0.0 Undec off X10 enabled ARC disabled AC enabled HomeEasy EU disabled Meiantech disabled Oregon Scientific disabled ATI disabled Visonic disabled Mertik disabled AD disabled Hideki disabled La Crosse disabled FS20 disabled ProGuard disabled BlindsT0 disabled BlindsT1 disabled AE disabled RUBiCSON disabled FineOffset disabled Lighting4 disabled RSL disabled RFU protocol 5 disabled RFU protocol 6 disabled
Code:
------------------------------------------------ 0B11000000A161B601010F60 Packettype = Lighting2 subtype = AC Sequence nbr = 0 ID = 0A161B6 Unit = 1 Command = On Signal level = 6 ------------------------------------------------ 0B11000100A161B601000060 Packettype = Lighting2 subtype = AC Sequence nbr = 1 ID = 0A161B6 Unit = 1 Command = Off Signal level = 6 ------------------------------------------------ 0B11000200A161B602010F50 Packettype = Lighting2 subtype = AC Sequence nbr = 2 ID = 0A161B6 Unit = 2 Command = On Signal level = 5 ------------------------------------------------ 0B11000300A161B602000060 Packettype = Lighting2 subtype = AC Sequence nbr = 3 ID = 0A161B6 Unit = 2 Command = Off Signal level = 6
Code:
Lighting2 command:0B 11 00 0E 00 A1 61 B6 01 01 06 00 ------------------------------------------------ 0402010E00 Packettype = Receiver/Transmitter Message subtype = Transmitter Response Sequence nbr = 14 response = ACK, data correct transmitted Lighting2 command:0B 11 00 0F 00 A1 61 B6 01 00 06 00 ------------------------------------------------ 0402010F00 Packettype = Receiver/Transmitter Message subtype = Transmitter Response Sequence nbr = 15 response = ACK, data correct transmitted Lighting2 command:0B 11 00 10 00 A1 61 B6 02 01 06 00 ------------------------------------------------ 0402011000 Packettype = Receiver/Transmitter Message subtype = Transmitter Response Sequence nbr = 16 response = ACK, data correct transmitted Lighting2 command:0B 11 00 11 00 A1 61 B6 02 00 06 00 ------------------------------------------------ 0402011100 Packettype = Receiver/Transmitter Message subtype = Transmitter Response Sequence nbr = 17 response = ACK, data correct transmitted
When I create the output device I set the address corresponding the ID of the AC module.
But I don't find how to set the Unit (1, 2 or 3)...
So when I try to change the state of the homeseer created device,it's not the correct command that is sent, so the module doesn't react...
May be I'm doing something wrong...
Thanks for your help
Comment